CFD1217
12" Drum Chipper
| Feed Type | Self Feed Drum |
| Chipping Capacity | 12 in |
| Standard Feed Rate | 120 fpm |
| Paint | Powder Coat |
| Weight (approx) | 4950 lb |
| Length (Transport) | 13 ft 10 in |
| Length (Operational) | 15 ft 10 in |
| Width | 6 ft 7 in |
| Height | 8 ft 2 in |
| Infeed Chute Size | 30 in H x 50 in W |
| Feed Roller Opening | 17 in W x 12 in H |
| Folding Table Size | 53 in W x 29 in L |
| Total Length from Ground to Nip Point | 94 in |
| Axle | 7000 lb Torflex With EZ Lube Bearings |
| Brakes | Electric (Self-Adjusting) |
| Tires | LT 245/75R-16E |
| Rims | 8 Lug - 1/2 in Stud 16 in x 6 in |
| Hydraulic Tank | 12 Gallon |
| Standard System Flow | 6 gpm |
| System Pressure | 2500 PSI |
| Hydraulic Filtration | In-Tank 10 Micron |
| Hydraulic Hoses Working Pressure | 3000 lb |
| Feed System Motor Displacement | 24.7 cu in |
| Frame Material | 2 in x 6 in Tubing | Front Jack | 5000 lb Lift |
| Tongue Length | 31 in | Hitch Height Adjustable | 2 Position 20 in to 24.5 in |
| Fuel Tank Composite | Steel 20 Gallon | Lighting | L.E.D. / DOT Compliant |
| Battery 12 Volt DC | CCA Diesel = 1000 Amps | Standard Battery Box | Composite |
| Standard Fenders | Black, non-skid fenders (steel) | Cutter Disc/Drum Size | 21 in Dia x 20 in W |
| Cutter Disc/Drum RPM / Weight | 2200 RPM / 425 lb | Disc/Drum Bearings | 2 7/16" Dia |
| Belt | Kevlar, Banded 4-Groove (B93) | Knives | (2) - 9 in x 4.5 in x 0.625 in Double-Edge |
| Anvil | 4-Sided 17.25 in x 3.5 in x 1 in | Drum/Disc Housing Material | 3/16 in Thick, High Strength Steel |
| Discharge Chute | 12 Gauge Wear plate / 360° Rotation |
| ANSI Z133.1 | Designed to Meet or Exceed |
| Panic Bar | Standard |
| Chip Deflector Curtain | Standard |
| Reversing Feed Rolls | Standard |
| Maintenance Cutter Lock | Standard |
| Slide Box Anchoring Pin | Standard |
| Engine Shutdown System (low oil/high temperature) | Standard |
| Controls Location | Curb Side |
| Safety and Instructional Decals | Standard |
| Safety Chains on Hitch | 3/8 in |
| 48 HP Kubota (Diesel) | Optional |
| 67 HP Kubota (Diesel) | Optional |
| 70 HP Ford 2.3L (Gas) | Optional |
| 84 HP John Deere (Diesel) | Optional |
| 85 HP Perkins (Diesel) | Optional |
| 85 HP Kubota (Diesel) | Standard |
| 99 HP Kubota (Gas) | Optional |
| Cone Holder | Optional | Caster Wheel Jackstand | Optional |
| FeedSense® Electronic Feed Control System | Standard | Debris Pusher | Optional |
| Fuel Tank Gauge | Standard | Flag Holders | Optional |
| Height Adjustable Discharge Chute | Standard | Hand-Crank Chute Rotation | Standard |
| Hydraulic Lift Cylinder | Standard | Hydraulic Oil Tank Gauge | Standard |
| Rear Jack Stand | Optional | Rear Engine Cut Off | Optional |
| Spare Tire / Rim | Optional | Single-Axle Frame Configuration | Standard |
| Strobe Light | Optional | Spring-Assist Folding Feed Table | Standard |
| Tool Box | Optional | Tire Change Jack Mounts | Standard |
| Winch | Optional | Wheel Chocks and Holders | Optional |
Altec Environmental Products 210 Inverness Center Drive, Birmingham, AL 35242
Phone: 800-958-2555 | Fax: 205-449-4774 | sales@altec.com